- #Toshiba color machine 2550c c3b1 registration#
- #Toshiba color machine 2550c c3b1 code#
- #Toshiba color machine 2550c c3b1 Pc#
MJ-1101 (When MJ-6103 is installed) Main power switch Turn OFF the main power switch, then back ON.
#Toshiba color machine 2550c c3b1 Pc#
Board check Finisher control PC board Board check.Check the connectors and harnesses between the converter PC board and the finisher controller PC board.
Setting of the equipment Check if the MJ-1101 is set as the specified finisher on the equipment.
Remedy: MJ-1101 Main power switch Turn OFF the main power switch, then back ON. Causes: Converter PC board Finisher control PC boardĬonverter PC board Finisher control PC board Hole punch control PC board. Description: Communication module SRAM reading failure. Board check 12 Mechanical section Sensor check 13 LGC board Board check. Harness check 11 Parts surrounding the 2nd transfer roller. 9 Is the 2nd transfer roller position detection sensor (S29) working properly? (Perform input check: 03-OFF//) Yes No 10 10 LGC board 8 One-way clutch gear at the end of the shaft Replace it. 7 Parts surrounding the 2nd transfer roller Check if there is any damage or abnormality. Board check 5 Is the 2nd transfer roller holding arm operated smoothly when it is pushed? Yes 8 No 6 6 2nd transfer roller pressure spring Check that the spring is installed properly (not running off the frame of the mold). #Toshiba color machine 2550c c3b1 registration#
Remedy: 1 Is the 2nd transfer roller's contact and release proper? (Perform output check: 03-239) Yes 9 No 2 2 Is the registration motor (M19) rotating? Yes 5 No 3 3 Registration motor (M19). Causes: Registration motor (M19) LGC board One-way clutch gear at the end of the shaft 2nd transfer roller position detection sensor (S29). Description: 2nd transfer roller releasing position detection abnormality. Board check 7 Mechanical section Sensor check 8 LGC board Board check. Board check 4 Is the 2nd transfer roller position detection sensor (S29) working properly? (Perform input check: 03-OFF//) Yes 7 No 5 5 2nd transfer roller position detection sensor (S29). Remedy: 1 Is the 2nd transfer roller's contact and release proper? (Perform output check: 03-239) Yes 4 No 2 2 Registration motor (M19). Causes: Registration motor (M19) LGC board 2nd transfer roller position detection sensor (S29). Description: 2nd transfer roller contacting position detection abnormality. Check the harnesses between the LGC board and the drawer connector for developer unit. Remedy: Drum thermistor Connector and harness check of drum thermistor K LGC board. Description: Drum thermistor-K abnormality: The output value of the drum thermistor-K is out of a specified range. #Toshiba color machine 2550c c3b1 code#
Drum phase adjustment control ON/OFF code 08-4766 0: Disabled 1: Enabled (Default) The setting value shall be returned after the recovery, otherwise color deviation increases. 11 LGC board Board checkĬE71 error can be prevented by setting the drum phase adjustment control OFF in the self-diagnostic code below. (Check if the mark on each gear is aligned with the area of the punched mark on the frame.) 10 Actuator Check if the actuator is installed properly.
Board check 9 Drum drive unit Check if the drive gears are installed properly. Check if there is any foreign matter such as grease in the detection area of the drum phase sensors (S43, S44). Check the connector of the drum phase sensors (S43, S44) and joint connectors. 
Are the drum phase sensors (Color drum phase sensor (S43) and K drum phase sensor (S44)) are operating properly? (Perform the input check: Color 03-OFF// K 03-OFF//.) Yes 9 No 7 7 Drum phase sensor (See the figure below.) If the rotation of the drum is extremely heavy or not smooth, check if the mechanism of the EPU is normal. Board check 5 Rotate the drum of each EPU in the direction of the arrow once.Yes 5 No 2 2 Drum motor (M10) Connector check 3 Drum drive unit Check if their drive gears are damaged or if they contact with the equipment. Is the drum motor (M10) operating properly? (Perform the output check: ON 03-101 / OFF 03-151.) * Check the operation after removing all process units (EPU (Y, M, C, K)).Is the error cleared after the power is turned OFF and then back ON?.Causes: Drum motor (M10) Drum drive unit.Description: Drum phase adjustment abnormality: Drum phase sensors (Color drum phase sensor (S43) and K drum phase sensor (S44)) are not turned ON after the drum motor was rotated for a specified period of time.
0 kommentar(er)
